How to replace some parts of the cone crusher
(1) cone crusher when the ore must be allocated in the middle of the plate, in order to prevent crusher overload,[url=http://www.xb-machine.com/Rotary_Kiln/Kaolin-RotaryKiln.html]Kaolin Rotary Kiln[/url] so that the liner wear is uneven; does not allow direct ore into the crushing cavity.The right to mine: ore distribution plate is uniformly dispersed in the crushing cavity, give into the ore can not be higher than the level of rolling acetabular wall. (2) the maximum crusher ore size 85% the size of the entrance to the mine, otherwise it will lead to a crusher lower yield, cone crusher,[url=http://www.xb-machine.com/Brick_making_machine/Fly-Ash-BrickMakingMachine.html]Fly Ash Brick Making Machine[/url] the damage of certain parts. (3) crushers do not load start, to avoid the accident. (4) parking, you must first stop to the mining machine, and the broken ore after discharge into the crushing chamber,Kaolin Rotary Kiln so that the crusher parking. (5) crushers work should always check the pressure and hydraulic locking system, identify problems and timely treatment. (6) the replacement of rolling acetabular wall rolling acetabular wall U-shaped screws on the adjusting ring, between the injection of zinc alloy, so closely integrated, the new installation or replacement of rolling acetabular wall, working 6-8 hours after should examine their retention and re-tighten the U-shaped screw. (7) cone crushing wall replacement cone crusher wall is tapered head fixed in the cone on the body between the two cast zinc alloy, a new installation or a new replacement cone crusher wall for 6-8 hours should be checked to solid, and found to immediately tighten the loose. (8) gear meshing friction circular plate wear, impact of changes in the gear gap in order to ensure the normal engagement of the gear must be in the bottom cover additional gasket, the gasket thickness should be equal to the amount of wear of the circular plate. Bearings and seals installed Bowl bearing (9), taking care not to make the rope break something slinger (hardwood and other objects to support the rope between).Assembly, [url=http://www.xb-machine.com/Crushing_Machinery/Sand-Making-Machine.html]Sand Making Machine[/url] the spherical bearing should be scraped to ensure that the crushing cone and bowl each other spherical outer contact with the inner ring should ensure that the annular gap of 0.35-0.5mm.Bowl bush around the perfusion bar alloy nail in the bowl bearing shelves, rotating along the circumferential how to prevent the bowl bearing.Bowl-shaped bearing frame and use (sales) and fixed in the work bowl bearing frame and the gap must be handled immediately. (10) cylindrical bushing and the frame body with the third transition, in order to prevent rotation of the bush in the bush the upper tank into a zinc alloy, and replace the new bushing should frame body size preparation. inevitably lead to the crusher after a long period of loading and unloading with the relationship between the change.If the gap is too general cause the bushing to rupture. Conical bushing taper sleeve and empty the eccentric shaft (11) to be strict co-injection of zinc alloy to prevent the sleeve rotation, the zinc alloy to be filled with all the gaps, the sake of hot the Note zinc alloy may cause deformation of the taper sleeve, so the new cone Set a good check size, [url=http://www.xb-machine.com/Crushing_Machinery/Jaw-Crusher.html]Jaw Crusher[/url] found to be incorrect should be promptly amended the actual size of the sets of the inner diameter of preparation in order to maintain the original with the manufacture of spare parts should be eccentric. The spring action of the spring (12) into the crusher protect the crusher can not be broken material is not damaged, so the spring pressure crusher crushing force to adapt to the crusher in the normal working hours spring is not moving,Dry Ball Mill just iron in the crushing chamber falling into the crusher overload when the lift supporting the occurrence of the phenomenon of the spring is compressed.Occur beating cone crusher upper part of the normal working hours, this is not a normal phenomenon must be carefully analyzed, the cause and take measures to remove the incorrectly compression spring not only does not work, but may occur part of the damage, because the compression spring will caused by the increase of the crushing force.Resulting in the upper part of the crusher beat the following several reasons: A, uneven ore to mine too much B, the ore contains too many small pieces and powdered ore or humidity is too large C port of discharge gap is too small. (13) exposed rotating part of the machine should be added to the shield.
About the Author
 | jonelistwens Xingbang Heavy Industrial Machinery Co., Ltd regards quality as life, customers as God, and serves our customers wholeheartedly by the principle of being brick making machineresponsible for every process, every product and every customer. All we do is for your sake and we firmly believe that quality is key to opening a market! |